请问你是什么牌?H3C Switch命令:
一、模式命令:
1. 用户模式:Switch>
2. 特权模式:Switch>enable
Switch#
3. 全局配置模式:Switch#config terminal
Switch(config)#
4. 接口配置模式:Switch(config)#interface fastethernet0/1
Switch(config-if)#
5. Line模式:Switch(config)#line console 0
Switch(config-line)#
二、特权模式下的命令:
1. 查看机MAC地址:Switch#show mac-address-table
2. 发现(CDP):
Switch#show cdp
Switch#show cdp interface fastethernet0/1
Switch#show cdp neighbors
Switch#show cdp neighbors detail
Switch#show cdp entry
3. 保存机配置:
Switch#copy running-config startup-config或者Switch#write
4. 恢复交换机出厂值:
Switch#erase startup-config
Switch#reload
三、全局配置模式下的命令:
1. 配置主机名:Switch(config)#hostname Sw1
Sw1(config)#
2、 设置登陆台密码:Switch(config)#line console 0
Switch(config-line)#password 密码
Switch(config-line)#login
3. 使能口令:Switch(config)#enable Password 密码
4. 加密保存的使能口令:Switch(config)#enable secret 密码
5. 配置IP地址:
Switch(config)#interface vlan 1
Switch(config-if)#ip address IP地址 网关
Switch(config-if)#no shutdown
6. 配置交换机网关:Switch(config)#ip default-gateway 网关
四、VLAN配置命令:
1. 创建vlan命令:
a) 全局配置模式下:
Switch(config)#vlan 2
Switch(config)#name v2
Switch(config)#mtu 数值
Switch(config)#end
b) Vlan数据库下:
Switch#vlan database
Switch#vlan 2 name v2
Switch#vlan 2 mut 数值
Switch#exit
2. 删除vlan命令:
a) 全局配置模式下:
Switch(config)#no vlan 2
Switch(config)#end
b) Vlan数据库下:
Switch#no vlan 2 name v2
Switch#exit
3. 在vlan中添加端口:
Switch#config terminal
Switch(config)#interface f0/1(端口)
Switch(config-if)#Switchport mode access
Switch(config-if)#switchport access vlan 2
Switch(config-if)#end
一次将多个端口添加到vlan中:
Switch#config terminal
Switch(config)#interface range f0/1 - 5(端口)
Switch(config-if)#switchport access vlan 2
Switch(config-if)#end
注:switch#show vlan biref(查看vlan信息)
4. 配置vlan trunk:
1. 配置接口为trunk命令:
Switch(config)# interface f0/1(端口)
Switch(config-if)#Switchport mode trunk
2. 配置接口为动态协商模式的命令:
Switch(config)# interface f0/1(端口)
Switch(config-if)#switchport mode dynamic desirable/auto
3. 从trunk中删除vlan:
Switch(config)# interface f0/1(端口)
Switch(config-if)#Switchport trunk allowed vlan remove 2
4. 在trunk中添加vlan:
Switch(config)# interface f0/1(端口)
Switch(config-if)#Switchport trunk allowed vlan add 2
-----------------------------------------------------------
Catalyst 2950交换机密码恢复
(1)拔下交换机的电源。
(2)用手按再交换机的MODE按键上,插上电源线。
(3)看到控制台出现如下提示,松开MODE建。
switch:
(4)再switch:后执行flash_init命令。
(5)查看Flash中的文件。
(6)把config.text文件改名为config.old文件。
(7)执行boot命令,启动交换机。
(8)进入特权模式查看flash里的文件。
(9)把文件config.old改为config.text文件。
(10)把config.text复制为系统的running-config.
(11)进入配置模式重新设置密码并存盘,密码恢复完成。
普通交换机常用配置命令?
a、更改远程TELNNET密码
Switch#configure terminal
Switch(config)#line vty 0 4
Switch(config-line)#password qycx123
Switch(config-line)#login
Switch(config-line)#exit
b、更改进入全局配置模式时的密码
Switch#configure terminal
Switch(config)#enable secret qycx123
思科交换机常用命令——创建并划分VLAN
a、创建VLAN
Switch#vlan database
Switch(vlan)#vlan 99 name office (创建vlan 99 并命名为office)
b、将端口划分至vlan
Switch(config)#interface fastEthernet 0/8
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 99 (将8号快速以太口划分至vlan 99)
思科交换机常用命令——调试命令
a、显示所有配置命令:Switch#show run
b、显示所有接口状态:Switch#show ip int brief
c、显示所有VLAN的信息:Switch#show vlan brief
cisco交换机还是比较常用的,于是我研究了一下Cisco交换机命令的大总结,在这里拿出来和大家分享一下,希望对大家有用。我所针对的都是Cisco的设备而言的,华为的可以跟据手册来查,配置都是差不多的,这里华子就不多写华为的设备了,了解的也不是很多。
Cisco交换机命令之使用Telnet远程式管理
switch(config)#interface vlan 1 进入vlan 1
switch(config-if)#ip address 设置IP地址
switch(config-if)#ip default-gateway 设置默认网关
switch(config)#line vty 0 4 进入虚拟终端
switch(config-line)#login 允许登录
switch(config-line)#password xx 设置登录口令
switch#exit 返回命令
Cisco交换机命令之控制台口令
switch(config)#line console 0 进入控制台口
switch(config-line)#login 允许登录
switch(config-line)#password xx 设置登录口令
switch#exit 返回命令
Cisco交换机命令之基本接口配置
switch(config)#interface f0/1 进入f0/1接口
switch(config-if)#duplex full 配置全双工模式
switch(config-if)#speed 100 配置速率
switch(config-if)#description to ***** 接口描述
switch(config)#ip domain-name ***.com 设置或名服务器
switch(config)#mac-address-table aging-time 设置mac表超时时间
switch#write 保存配置信息
switch#copy running-config startup-config 保存当前配置nvram
switch#erase startup-config 清除配置文件
Cisco交换机命令之交换机VLAN设置:
switch#vlan database 进入VLAN设置
switch(vlan)#vlan 2 建VLAN 2
switch(vlan)#name 名字 建VLAN 2的名称
switch(vlan)#no vlan 2 删vlan 2
注:删除vlan时原属于此vlan的端口处于非激活状态,直到重新分配为止。
switch(config)#int f0/1 进入端口1
switch(config-if)#switchport mode access 当前端口工作莫试
switch(config-if)#switchport access vlan 2 当前端口加入vlan 2
switch(config-if)#switchport mode trunk 设置为干线
switch(config-if)#switchport trunk encapsulation dot1q 设置vlan 中继协议
switch(config-if)#no switchport mode 或 ( switchport mode access) 禁用干线
switch(config-if)#switchport trunk allowed vlan add 1,2 ; 从Trunk中添加vlans
switch(config-if)#switchport trunk allowed vlan remove 1,2 ;从Trunk中删除vlans
switch(config-if)#switchport trunk pruning vlan remove 1,2 ;从Trunk中关闭局部修剪
Cisco交换机命令之以太网通道配置
switch(config)#interface range fasternet0/1 - 2 将fasternet0/1和0/2 口捆绑
switch(config-if)#channel-group 1 mode on 配置以太通道模式
switch(config-if)#port-channel load-balance {dst-mac | src-mac}在链路间实现负载均衡
switch#show etherchannel 1 summary 查看通道信息
switch#show etherchannel load-balance 查看通道信息
Cisco交换机命令之vtp配置
switch(config)#vtp domain 设置vtp域名
switch(config)#vtp password 设置vtp密码
switch(config)#vtp mode server 设置vtp服务器模式
switch(config)#vtp mode client 设置vtp客户机模式
switch(config)#vtp mode transparent 设置vtp 透明模式
switch(config)#vtp version 设置vtp版本
switch(config)#vtp pruning 启用vtp修解
switch(config)#no vtp pruning 关闭vtp修解
注:要想从vtp中减少一台交换机只需将该交换机vtp 名更改
Cisco交换机命令之生成树stp:
switch(config)#spanning-tree vlan 启用stp生成树(基于vlan)
switch(config)#spanning-tree vlan root primary 指定根交换机(基于vlan)
switch(config)#spanning-tree vlan root secondary 指定备用根交换机(基于vlan)
switch(config)#spanning-tree vlan priority 指定交换机优先级(基于vlan)
switch(config)#no spanning-tree vlan priority 将交换机的优先级恢复默认值(基于vlan)
switch(config-if)#spanning-tree vlan cost 指定端口成本(起用trunk的端口模式下)
switch(config-if)#spanning-tree vlan port-prioty 指定交换机端口优先级(基于vlan)
switch(config-if)#spanning-tree portfast 配置速端口(连接终端设备的端口状态)如pc机
switch(config)#spanning-tree uplinkfast 配置上行速端口
switch(config)#spanning-tree vlan hello-time 配置交换机hello时间(基于vlan)
switch(config)#spanning-tree vlan forward-time 修改转发延迟计时器(基于vlan)
switch(config)#spanning-tree vlan max-time 修改最大老化时间(基于vlan)
switch#show spanning-tree summery 检测vlan生成树配置
switch#show spanning-tree vlan detail 浏览详细生成树配置信息
switch#show spanning-tree interface detail 浏览详细生成树端口配置信息
Cisco交换机命令之交换机显示命令:
switch#show vtp status 查看vtp配置信息
switch#show running-config 查看当前配置信息
switch#show vlan 查看vlan配置信息
switch#show interface 查看端口信息
switch#show int f0/0 查看指定端口信息
switch#dir flash: 查看闪存
switch#show version 查看当前版本信息
switch#show mac-address-table aging-time 查看mac超时时间
switch#show cdp cisco设备发现协议 (可以查看聆接设备)
switch#show cdp traffic 杳看接收和发送的cdp包统计信息
switch#show cdp neighbors 查看与该设备相邻的cisco设备
switch#show interface f0/1 switchport 查看有关switchport的配置
switch#show cdp neighbors 查看与该设备相邻的cisco设备
二层交换机为什么要配置IP地址
首先回答你第一个问题,交换机和PC是二层通信,因此他们之间靠的是MAC地址来通信,不会应用到ARP广播,它是三层的信息,就是在有路由的情况下才会用到它。
原理也很简单,因为你设置的IP和你绑定的IP冲突了,但是你在子网内通信也是属于二层通信。但是你要到达路由器的话,就要看你是怎样设置的了。
我跟你说以下路由器与PC得工作原理。
假如说有两台主机A B,它两也不再同一网段中,那么就要有三层的设备路由器来转发了。当主机A要与B通信时,A主机的数据包先到达自己的网关,然后主机A会通过ARP请求得知自己网关的MAC地址。在数据链路层A将IP数据包写入到以太网帧的数据包中。帧中的源MAC和目的MAC,分别是主机A 和网关的MAC地址。那么这个数据包就会到达A相连的路由器,路由器会重新打开以太网的数据帧,查看里面的信息。它会匹配路由表的条目,如果有在写入自己去B主机的接口的MAC,然后就这样依次类推。当到了对方是做的相反的动作。
怎样在锐捷交换机上配置vrrp、arp和mstp..
慢慢研究 、。。。。。。老师留的问题别老找枪手
交换机
密码
1234(config)#enable secret level 1 0 100
1234(config)#enable secret level 15 0 100
远程登入密码
1234(config)#line vty 0 4
1234(config-line)#password 100
1234(config-line)#end
交换机管理IP
1234(config)#interface vlan 1
1234(config-if)#ip address 192.168.1.10 255.255.255.0
1234(config-if)#no shutdown
修改交换机老化时间
1234(config)#mac-address-table aging-time 20
1234(config)#end
添删vlan
1234(config)#vlan 888
1234(config-vlan)#name a888
1234(config)#no vlan 888
添加access口
1234(config)#interface gigabitEthernet 0/10
1234(config-if)#switchport mode access
1234(config-if)#switchport access vlan 10
切换assess trunk
1234(config-if)#switchport mode access
1234(config-if)#switchport mode trunk
指定特定一个native vlan
1234(config-if)#switchport trunk native vlan 10
配置trunk口的许可vlan列表
1234(config-if)#switchport trunk allowed vlan ?
add Add VLANs to the current list
all All VLANs
except All VLANs except the following
remove Remove VLANs from the current list
速成树协议
1234(config)#spanning-tree
1234(config)#spanning-tree mode rstp/stp
配置网关:
switch(config)#ip default-gateway 192.168.1.254
交换机基本配置-常见查看命令
查看CPU利用率
show cpu
查看交换机时钟
show clock
查看交换机日志
show logging
查看交换机动态学习到的MAC地址表
show mac-address-table dynamic
查看当前交换机运行的配置文件
show running-config
查看交换机硬件、软件信息
show version
查看交换机的arp表
show arp
显示接口详细信息的命令
show interfaces gigabitEthernet 4/1 counters
接口配置
Switch(config)#interface gigabitethernet 0/1
把接口工作模式改为光口。
Switch(config-if)#medium-type fiber
把接口工作模式改为电口。
Switch(config-if)#medium-type copper
速度/双工配置
进入接口配置模式。
Switch(config)#interface interface-id
设置接口的速率参数,或者设置为auto。
Switch(config-if)#speed {10 | 100 | 1000 | auto }
设置接口的双工模式。
Switch(config-if)#duplex {auto | full | half}
例子
Switch(config)#interface gigabitethernet 0/1
Switch(config-if)#speed 1000
Switch(config-if)#duplex full
光口不能修改速度和双工配置,只能auto。
在故障处理的时候,如果遇到规律性的时断时续或掉包,在排除其他原因后,可以考虑是否和对端设备的速率和双工模式不匹配,尤其是两端设备为不同厂商的时候。
VLAN
建立VLAN 100
Switch (config)#vlan 100
该VLAN名称为ruijie
Switch (config)#name ruijie
将交换机接口划入VLAN 中:
range表示选取了系列端口1-48,这个对多个端口进行相同配置时非常有用。
Switch (config)#interface range f 0/1-48
将接口划到VLAN 100中。
Switch (config-if-range)#switchport access vlan 100
将接口划回到默认VLAN 1中,即端口初始配置。
Switch (config-if-range)#no switchport access vlan
Switch(config)#interface fastEthernet 0/1
该端口工作在access模式下
Switch(config-if)#switchport mode access
该端口工作在trunk模式下
Switch(config-if)#switchport mode trunk
Switch(config)#interface fastEthernet 0/2
设定VLAN要修剪的VLAN。
Switch(config-if)#switchport trunk allowed vlan remove 2-9,11-19,21-4094
取消端口下的VLAN修剪。
Switch(config-if)#no switchport trunk allowed vlan
生成树
开启生成树协议。
Switch(config)#spanning-tree
禁止生成树协议。
Switch(config)#no spanning-tree
配置生成树优先级:
配置设备优先级为4096。
Switch(config)#spanning-tree priority 4096
数值越低,优先级别越高。
端口镜像
配置G0/2为镜像端口。
Switch (config)# monitor session 1 destination interface G 0/2
配置G0/1为被镜像端口,且出入双向数据均被镜像。
Switch (config)# monitor session 1 source interface G 0/1 both
去掉镜像1。
Switch (config)# no monitor session 1
端口聚合
Switch(config)#interface fastEthernet 0/1
把端口f0/1加入到聚合组1中。
Switch (config-if)#port-group 1
把端口f0/1从聚合组1中去掉
Switch (config-if)#no port-group 1
建立ACL:
建立ACL访问控制列表名为ruijie,extend表示建立的是扩展访
Switch(config)# Ip access-list exten ruijie
问控制列表。
添加ACL的规则:
禁止PING IP地址为192.168.1.1的设备。
Switch (config-ext-nacl)#deny icmp any 192.168.1.1 255.255.255.0
禁止端口号为135的应用。
Switch (config-ext-nacl)# deny tcp any any eq 135
禁止协议为www的应用。
Switch (config-ext-nacl)#deny udp any any eq www
允许所有行为。
Switch(config-ext-nacl)# permit ip any any
将ACL应用到具体的接口上:
Switch (config)#interface range f 0/1
把名为ruijie的ACL应用到端口f 0/1上。
Switch (config-if)#ip access-group ruijie in
从接口去除ACL。
Switch (config-if)#no ip access-group ruijie in
删除ACL:
删除名为ruijie的ACL。
Switch(config)#no Ip access-list exten ruijie
增加ACE项后,是增加到ACL最后,不可以中间插入,如果要调整ACE的顺序,必须整个删除ACL后再重新配置。
端口安全
Switch (config)#interface range f 0/1
开启端口安全。
Switch(config-if)# switchport port-security
关闭端口安全。
Switch(config-if)# no switchport port-security
设置端口能包含的最大安全地址数为8。
Switch(config-if)# switchport port-security maximum 8
在接口fastethernet0/1配置一个安全地址00d0.f800.073c,并为其绑定一个IP地址192.168.1.1
Switch(config-if)# switchport port-security mac-address 00d0.f800.073c ip-address 192.168.1.1
删除接口上配置的安全地址。
Switch(config-if)#no switchport port-security mac-address 00d0.f800.073c ip-address 192.168.1.1
防ARP攻击
IP和MAC地址的绑定
Switch(config)#arp ip-address hardware-address [type] interface-id
Switch(config)#arp 192.168.12.111 00d0.f800.073c arpa g 0/1
绑定网关
进入指定端口进行配置。
Switch(config)#Interface interface-id
配置防止ip-address的ARP欺骗。
Switch(config-if)#Anti-ARP-Spoofing ip ip-address
防STP攻击
进入端口Fa0/1。
Switch(config)# inter fastEthernet 0/1
打开该端口的的BPDU guard功能。
Switch(config-if)# spanning-tree bpduguard enable
关闭该端口的的BPDU guard功能。
Switch(config-if)# spanning-tree bpduguard diaable
端口关闭后只能shutdown然后再no shutdown
或者重新启动交换机才能恢复!
防DOS/DDOS攻击
进入端口Fa0/1。
Switch(config)# inter fastEthernet 0/1
预防伪造源IP的DOS攻击的入口过滤功能。
Switch(config-if)#ip deny spoofing-source
关闭入口过滤功能只能在三层接口上配置。
Switch(config-if)#no ip deny spoofing-source
和ACL不能同时存在。
端口关闭后只能shutdown然后再no shutdown
或者重新启动交换机才能恢复!
防IP扫描攻击配置:
打开系统保护。
Switch(config)#system-guard enable
关闭系统保护功能。
Switch(config)#no system-guard
DHCP配置
打开DHCP Relay Agent:
Switch(config)#service dhcp
配置DHCP Server的IP地址:
Switch(config)#ip helper-address address
VRRP配置
Switch(config)#Interface interface-id
Switch(config-if)#Standby [group-number] ip ip-address
设置虚拟机的优先级。
standby [group-number] priority priority
三层交换机配置
SVI:
把VLAN 10配置成SVI。
switch (config)#interface vlan 10
给该SVI接口配置一个IP地址
switch (config-if)#ip address 192.168.1.1 255.255.255.0
Routed Port:
switch (config)#interface fa 0/1
把f 0/1变成路由口。
switch (config-if)#no switch
路由配置:
添加一条路由。
switch (config)#ip route 目的地址 掩码 下一跳
switch (config)#ip route 210.10.10.0 255.255.255.0 218.8.8.8
思科路由器和交换机的配置命令全集
1. switch配置命令
(1)模式转换命令
用户模式----特权模式,使用命令"enable"
特权模式----全局配置模式,使用命令"config t"
全局配置模式----接口模式,使用命令"interface+接口类型+接口号"
全局配置模式----线控模式,使用命令"line+接口类型+接口号"
注:
用户模式:查看初始化的信息.
特权模式:查看所有信息、调试、保存配置信息
全局模式:配置所有信息、针对整个路由器或交换机的所有接口
接口模式:针对某一个接口的配置
线控模式:对路由器进行控制的接口配置
(2)配置命令
show running config 显示所有的配置
show versin 显示版本号和寄存器值
shut down 关闭接口
no shutdown 打开接口
ip add +ip地址 配置IP地址
secondary+IP地址 为接口配置第二个IP地址
show interface+接口类型+接口号 查看接口管理性
show controllers interface 查看接口是否有DCE电缆
show history 查看历史记录
show terminal 查看终端记录大小
hostname+主机名 配置路由器或交换机的标识
config memory 修改保存在NVRAM中的启动配置
exec timeout 0 0 设置控制台会话超时为0
service password-encryptin 手工加密所有密码
enable password +密码 配置明文密码
ena sec +密码 配置密文密码
line vty 0 4/15 进入telnet接口
password +密码 配置telnet密码
line aux 0 进入AUX接口
password +密码 配置密码
line con 0 进入CON接口
password +密码 配置密码
bandwidth+数字 配置带宽
no ip address 删除已配置的IP地址
show startup config 查看NVRAM中的配置信息
copy run-config atartup config 保存信息到NVRAM
write 保存信息到NVRAM
erase startup-config 清除NVRAM中的配置信息
show ip interface brief 查看接口的谪要信息
banner motd # +信息 + # 配置路由器或交换机的描素信息
description+信息 配置接口听描素信息
vlan database 进入VLAN数据库模式
vlan +vlan号+ 名称 创建VLAN
switchport access vlan +vlan号 为VLAN为配接口
interface vlan +vlan号 进入VLAN接口模式
ip add +ip地址 为VLAN配置管理IP地址
vtp+service/tracsparent/client 配置SW的VTP工作模式
vtp +domain+域名 配置SW的VTP域名
vtp +password +密码 配置SW的密码
switchport mode trunk 启用中继
no vlan +vlan号 删除VLAN
show spamming-tree vlan +vlan号 查看VLA怕生成树议
2. 路由器配置命令
ip route+非直连网段+子网掩码+下一跳地址 配置静态/默认路由
show ip route 查看路由表
show protocols 显示出所有的被动路由协议和接口上哪些协议被设置
show ip protocols 显示了被配置在路由器上的路由选择协议,同时给出了在路由选择协议中使用
的定时器
等信息
router rip 激活RIP协议
network +直连网段 发布直连网段
interface lookback 0 激活逻辑接口
passive-interface +接口类型+接口号 配置接口为被动模式
debug ip +协议 动态查看路由更新信息
undebug all 关闭所有DEBUG信息
router eigrp +as号 激活EIGRP路由协议
network +网段+子网掩码 发布直连网段
show ip eigrp neighbors 查看邻居表
show ip eigrp topology 查看拓扑表
show ip eigrp traffic 查看发送包数量
router ospf +process-ID 激活OSPF协议
network+直连网段+area+区域号 发布直连网段
show ip ospf 显示OSPF的进程号和ROUTER-ID
encapsulation+封装格式 更改封装格式
no ip admain-lookup 关闭路由器的域名查找
ip routing 在三层交换机上启用路由功能
show user 查看SW的在线用户
clear line +线路号 清除线路
3. 三层交换机配置命令
配置一组二层端口
configure terminal 进入配置状态
nterface range {port-range} 进入组配置状态
配置三层端口
configure terminal 进入配置状态
interface {{fastethernet | gigabitethernet} interface-id} | {vlan vlan-id} | {port-
channel port-channel-number} 进入端口配置状态
no switchport 把物理端口变成三层口
ip address ip_address subnet_mask 配置IP地址和掩码
no shutdown 激活端口
例:
Switch(config)# interface gigabitethernet0/2
Switch(config-if)# no switchport
Switch(config-if)# ip address 192.20.135.21 255.255.255.0
Switch(config-if)# no shutdown
配置VLAN
configure terminal 进入配置状态
vlan vlan-id 输入一个VLAN号, 然后进入vlan配态,可以输入一个新的VLAN号或旧的来进行修改
。
name vlan-name 可选)输入一个VLAN名,如果没有配置VLAN名,缺省的名字是VLAN号前面用0填满
的4位数,如VLAN0004是VLAN4的缺省名字
mtu mtu-size (可选) 改变MTU大小
例
Switch# configure terminal
Switch(config)# vlan 20
Switch(config-vlan)# name test20
Switch(config-vlan)# end
或
Switch# vlan database
Switch(vlan)# vlan 20 name test20
Switch(vlan)# exit
将端口分配给一个VLAN
configure terminal 进入配置状态
interface interface-id 进入要分配的端口
switchport mode access 定义二层口
switchport access vlan vlan-id 把端口分配给某一VLAN
例
Switch# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)# interface fastethernet0/1
Switch(config-if)# switchport mode access
Switch(config-if)# switchport access vlan 2
Switch(config-if)# end
Switch#
配置VLAN trunk
configure terminal 进入配置状态
interface interface-Id 进入端口配置状态
switchport trunk encapsulation {isl | dot1q | negotiate}配置trunk封装ISL 或 802.1Q 或
自动协商
switchport mode {dynamic {auto | desirable} | trunk} 配置二层trunk模式。
dynamic auto—自动协商是否成为trunk
dynamic desirable—把端口设置为trunk如果对方端口是trunk, desirable, 配置Native VLAN
(802.1q)
或自动模式,trunk—设置端口为强制的trunk方式,而不理会对方端口是否为trunk
switchport access vlan vlan-id 可选) 指定一个缺省VLAN, 如果此端口不再是trunk
switchport trunk native vlan vlan-id 指定802.1Q native VLAN号
例:
Switch# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)# interface fastethernet0/4
Switch(config-if)# switchport mode trunk
Switch(config-if)# switchport trunk encapsulation dot1q
Switch(config-if)# end
定义TRUNK允许的VLAN
configure terminal子 进入配置状态
interface interface-id 进入端口配置
switchport mode trunk 配置二层口为trunk
switchport trunk allowed vlan {add | all | except | remove} vlan-list可选) 配置trunk允
许的VLAN.使用add, all, except, remove关健字
no switchport trunk allowed vlan 允许所有VLAN通过
例
Switch(config)# interface fastethernet0/1
Switch(config-if)# switchport trunk allowed vlan remove 2
Switch(config-if)# end
配置Native VLAN(802.1q)
configure terminal 进入配置状态
interface interface-id 进入配置成802.1qtrunk的端口
switchport trunk native vlan vlan-Id 配置native VLAN号
no switchport trunk native vlan 端口配置命令回到缺省的状态
配置基于端口权值的负载均衡
configure terminal 进入Switch 1配置状态
vtp domain domain-name 配置VTP域
vtp mode server 将Switch 1配置成VTP server.
show vtp status 验证VTP的配置
show vlan 验证VLAN
configure terminal 进入配置状态
interface fastethernet 0/1 进入F0/1端口
switchport trunk encapsulation {isl | dot1q | negotiate}配置trunk封装
switchport mode trunk 配置成trunk
show interfaces fastethernet0/1 switchport 验证VLAN配置
按以上步骤对想要负载均衡的接口进行配置
在另一个交换机上进行此配置
show vlan 当trunk已经起来,在switch2上验证已经学到相的vlan配置
configure terminal 在Switch 1上进入配置状态
interface fastethernet0/1 进入要配置的端口
spanning-tree vlan 8 port-priority 10 将端口权值10赋与VLAN 8.
spanning-tree vlan 9 port-priority 10 将端口权值10赋与VLAN 9.
spanning-tree vlan 10 port-priority 10 将端口权值10赋与VLAN 10.
interface fastethernet0/2 进入F0/2
spanning-tree vlan 3 port-priority 10 将端口权值10赋与VLAN 3.
spanning-tree vlan 4 port-priority 10 将端口权值10赋与VLAN 4
spanning-tree vlan 5 port-priority 10 将端口权值10赋与VLAN 5
spanning-tree vlan 6 port-priority 10 将端口权值10赋与VLAN 10
end 退出
show running-config 验证配置
copy running-config startup-config 保存配置
配置STP路径值的负载均衡
Trunk1走VLAN8-10,Trunk2走VLAN2-4
configure terminal 进入 Switch 1配置状态
interface fastethernet 0/1 进入F0/1
switchport trunk encapsulation {isl | dot1q | negotiate}配置封装
switchport mode trunk 配置Trunk,缺省是ISL封装
exit 退回
在F0/2口上重复2-4步骤
exit 退回
show running-config 验证配置
show vlan验证switch1 已经学到Vlan
configure terminal 进入配置状态
interface fastethernet 0/1 进入F0/1
spanning-tree vlan 2 cost 30 设置Vlan2生成树路径值为30
spanning-tree vlan 3 cost 30 设置Vlan3生成树路径值为30
spanning-tree vlan 4 cost 30 设置Vlan4生成树路径值为30
end 退出
在switch1的F0/2上重复9-11步骤设置VLAN8,9,10生成树路径值为30
end 退出
show running-config 验证配置
copy running-config startup-config 保存配置
补充:CISCO命令集——路由选择协议及排障
*ip route命令
Router(config)# ip route <目录网络或子网号> [子网掩码] <下一路由器IP地址 | 从本地出口
的地址> [管理距离0~255,默认为1]
(注:静态地址配置)
*ip default-network命令
Router(config)# ip default-network <目标网络号>
(注:配合路由协使用,用其中的一个动态路由号作默认路由配置)
Router(config)# ip route 0.0.0.0 0.0.0.0 <下一路由器IP地址 | 从本地出口的地址>
(注:只有一个公网地址时,在出口路由器上的配置)
*内部路由选择协议
*使用router和network命令
Router(config)# router <路由协议rip | igrp | eigrp | ospf | is-is等> [自主系统号]
Router(config-router)# network <直接相连的要用此路由协议的网络号>
Router(config-router)# network <直接相连的要用此路由协议的网络号>
*路由信息协议RIP
Router(config)# router rip
Router(config-router)# network <直接相连的要用rip协议的有类别网络号>
Router# show ip protocols
Router# show ip route
Router# debug ip rip
*内部网关路由协议IGRP
Router(config)# router igrp <自主系统号>
Router(config-router)# network <直接相连的要用igrp协议的有类别网络号>
Router# show ip interface
Router# show ip protocols
Router# show ip route
Router# debug ip rip
*排除网络故障
排除网络故障的一个总体模型
Router# ping <有故障的主机 | 有故障的IP地址>
Router# show ip route
Router# show interface <有故障的接口>
Router# show run
*IP的故故障排除
检查可用的路由
Router# show ip route <有故障的IP地址>
27.4.4 跟踪路由(Tracing the Route)
SUN-A> traceroute <有故障的主机 | 有故障的IP地址>
C:\windows\> winipcfg
C:\windows\> ipconfig
C:\windows\> ipconfig / all
C:\windows\> tracert <有故障的主机 | 有故障的IP地址>
使用扩展的ping来跟踪连接性
Router# ping
*其它可能的故障
一个地址解析(ARP)的故障
Router# show arp
Router# show interface <有故障的接口>
C:\windows\> arp -a
SUN-A> arp –a
验证终端系统的路由表
C:\windows\> netstat –rn
C:\windows\> route –f add 0.0.0.0 mask 0.0.0.0 <需要添加入的网关地址>
C:\windows\> route [–f ] [[print | add | delete | change] [destination] [mask
netmask] [gateway]]
C:\windows\> route add mask <网络掩码> <网关ip地址>
C:\windows\> route delete mask <网络掩码> <网关ip地址>
C:\windows\> nbtstat <相应的参数>
SUN-A> netstat -rn路由器
华为3600交换机配置问题
#
local-user admin
password simple admin
service-type telnet
level 3
#
user-interface vty 0 4
authentication-mode scheme
#用户部分
#
vlan 2
#
interface e1/0/1
...
int e1/0/20
默认都属于vlan1
int e1/0/20
port access vlan 2 加入到vlan2 也就是连接主线的。
#
int vlan 1
IP address 10.20.9.1 255.255.255.0 本地用户vlan
#
int vlan 2
IP address 172.30.0.37 255.255.255.252 很明显这是互联vlan。
#
ip rou 0.0.0.0 0.0.0.0 172.30.0.38
#
snmp-agent
snmp-agent community read public
snmp-agent community write private
snmp-agent sys-info version all
#
vlan3 没起作用。这个相当于最后显示出来的效果。一步步实施就不用写了吧。其实很简单的一个配置,做2个vlan一个本地用户接入vlan。一个连接上级的互联vlan,掩码都掩到30位了,就2个可用ip地址。指个路由就行了。上级还应该把本地用户段的路由在指回来。既然是替换就不用管了。
想学学交换机配置?
思科交换机配置
switch> 用户模式
1:进入特权模式 enable
switch> enable
switch#
2:进入全局配置模式 configure terminal
switch> enable
switch#c onfigure terminal
switch(conf)#
3:交换机命名 hostname aptech2950 以aptech2950为例
switch> enable
switch#c onfigure terminal
switch(conf)#hostname aptch-2950
aptech2950(conf)#
4:配置使能口令 enable password cisco 以cisco为例
switch> enable
switch#c onfigure terminal
switch(conf)#hostname aptch2950
aptech2950(conf)# enable password cisco
5:配置使能密码 enable secret ciscolab 以cicsolab为例
switch> enable
switch#c onfigure terminal
switch(conf)#hostname aptch2950
aptech2950(conf)# enable secret ciscolab
6:设置虚拟局域网vlan 1 interface vlan 1
switch> enable
switch#c onfigure terminal
switch(conf)#hostname aptch2950
aptech2950(conf)# interface vlan 1
aptech2950(conf-if)#ip address 192.168.1.1 255.255.255.0 配置交换机端口ip和子网掩码
aptech2950(conf-if)#no shut 是配置处于运行中
aptech2950(conf-if)#exit
aptech2950(conf)#ip default-gateway 192.168.254 设置网关地址
7:进入交换机某一端口 interface fastehernet 0/17 以17端口为例
switch> enable
switch#c onfigure terminal
switch(conf)#hostname aptch2950
aptech2950(conf)# interface fastehernet 0/17
aptech2950(conf-if)#
8:查看命令 show
switch> enable
switch# show version 察看系统中的所有版本信息
show interface vlan 1 查看交换机有关ip 协议的配置信息
show running-configure 查看交换机当前起作用的配置信息
show interface fastethernet 0/1 察看交换机1接口具体配置和统计信息
show mac-address-table 查看mac地址表
show mac-address-table aging-time 查看mac地址表自动老化时间
9:交换机恢复出厂默认恢复命令
switch> enable
switch# erase startup-configure
switch# reload
10:双工模式设置
switch> enable
switch#c onfigure terminal
switch2950(conf)#hostname aptch-2950
aptech2950(conf)# interface fastehernet 0/17 以17端口为例
aptech2950(conf-if)#duplex full/half/auto 有full , half, auto 三个可选项
11:cdp相关命令
switch> enable
switch# show cdp 查看设备的cdp全局配置信息
show cdp interface fastethernet 0/17 查看17端口的cdp配置信息
show cdp traffic 查看有关cdp包的统计信息
show cdp nerghbors 列出与设备相连的cisco设备
12:csico2950的密码恢复
拔下交换机电源线。
用手按着交换机的MODE键,插上电源线
在switch:后执行flash_ini命令:switch: flash_ini
查看flash中的文件: switch: dir flash:
把“config.text”文件改名为“config.old”: switch: rename flash: config.text flash: config.old
执行boot: switch: boot
交换机进入是否进入配置的对话,执行no :
进入特权模式察看flash里的文件: show flash :
把“config.old”文件改名为 “config.text”: switch: rename flash: config.old flash: config.text
把“config.text”拷入系统的“running-configure”: copy flash: config.text system : running-configure
把配置模式重新设置密码存盘,密码恢复成功。
13:交换机telnet远程登录设置:
switch>en
switch#c onfigure terminal
switch(conf)#hostname aptech-2950
aptech2950(conf)#enable password cisco 以cisco为特权模式密码
aptech2950(conf)#interface fastethernet 0/1 以17端口为telnet远程登录端口
aptech2950(conf-if)#ip address 192.168.1.1 255.255.255.0
aptech2950(conf-if)#no shut
aptech2950(conf-if)#exit
aptech2950(conf)line vty 0 4 设置0-4 个用户可以telnet远程登陆
aptech2950(conf-line)#login
aptech2950(conf-line)#password edge 以edge为远程登录的用户密码
主机设置:
ip 192.168.1.2 主机的ip必须和交换机端口的地址在同一网络段
netmask 255.255.255.0
gate-way 192.168.1.1 网关地址是交换机端口地址
运行:
telnet 192.168.1.1
进入telnet远程登录界面
password : edge
aptech2950>en
password: cisco
aptech#
14:交换机配置的重新载入和保存
设置完成交换机的配置后:
aptech2950(conf)#reload
是否保存(y/n) y: 保存设置信息 n:不保存设置信息1.在基于IOS的交换机上设置主机名/系统名:
switch(config)# hostname hostname
在基于CLI的交换机上设置主机名/系统名:
switch(enable) set system name name-string2.在基于IOS的交换机上设置登录口令:
switch(config)# enable password level 1 password
在基于CLI的交换机上设置登录口令:
switch(enable) set password
switch(enable) set enalbepass3.在基于IOS的交换机上设置远程访问:
switch(config)# interface vlan 1
switch(config-if)# ip address ip-address netmask
switch(config-if)# ip default-gateway ip-address
在基于CLI的交换机上设置远程访问:
switch(enable) set interface sc0 ip-address netmask broadcast-address
switch(enable) set interface sc0 vlan
switch(enable) set ip route default gateway4.在基于IOS的交换机上启用和浏览CDP信息:
switch(config-if)# cdp enable
switch(config-if)# no cdp enable
为了查看Cisco邻接设备的CDP通告信息:
switch# show cdp interface [type modle/port]
switch# show cdp neighbors [type module/port] [detail]
在基于CLI的交换机上启用和浏览CDP信息:
switch(enable) set cdp {enable|disable} module/port
为了查看Cisco邻接设备的CDP通告信息:
switch(enable) show cdp neighbors[module/port] [vlan|duplex|capabilities|detail]5.基于IOS的交换机的端口描述:
switch(config-if)# description description-string
基于CLI的交换机的端口描述:
switch(enable)set port name module/number description-string6.在基于IOS的交换机上设置端口速度:
switch(config-if)# speed{10|100|auto}
在基于CLI的交换机上设置端口速度:
switch(enable) set port speed moudle/number {10|100|auto}
switch(enable) set port speed moudle/number {4|16|auto}7.在基于IOS的交换机上设置以太网的链路模式:
switch(config-if)# duplex {auto|full|half}
在基于CLI的交换机上设置以太网的链路模式:
switch(enable) set port duplex module/number {full|half}8.在基于IOS的交换机上配置静态VLAN:
switch# vlan database
switch(vlan)# vlan vlan-num name vlaswitch(vlan)# exit
switch# configure teriminal
switch(config)# interface interface module/number
switch(config-if)# switchport mode access
switch(config-if)# switchport access vlan vlan-num
switch(config-if)# end
在基于CLI的交换机上配置静态VLAN:
switch(enable) set vlan vlan-num [name name]
switch(enable) set vlan vlan-num mod-num/port-list9. 在基于IOS的交换机上配置VLAN中继线:
switch(config)# interface interface mod/port
switch(config-if)# switchport mode trunk
switch(config-if)# switchport trunk encapsulation {isl|dotlq}
switch(config-if)# switchport trunk allowed vlan remove vlan-list
switch(config-if)# switchport trunk allowed vlan add vlan-list
在基于CLI的交换机上配置VLAN中继线:
switch(enable) set trunk module/port [on|off|desirable|auto|nonegotiate]
Vlan-range [isl|dotlq|dotl0|lane|negotiate]10.在基于IOS的交换机上配置VTP管理域:
switch# vlan database
switch(vlan)# vtp domain domain-name
在基于CLI的交换机上配置VTP管理域:
switch(enable) set vtp [domain domain-name]
。。。 。。。
PacketTracer5模拟器,
转载请注明出处51数据库 » removevtypassword 交换机配置命令